| Section | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
| Warning |
|---|
| When you press 'esc' keyboard during adding a group, this will be canceled. Don't press this during this job. |
Adding and Deleting Resource Group
- To add a group, select 'group name->right click->Add Group' from configuration tree.
Or select 'Edit(E)->Add Group' from main menu.
[Figure] Adding a Group from configuration tree
[그림] 그룹 등록 화면 -툴바의 등록 버튼
[그림] 그룹 등록 화면 - 편집 메뉴의 그룹 등록 - Add Group wizard is launched as shown below.
[Figure] Initial Add Group View - Enter group name, select the nodes from Available nodes list and click the '▶' button to moves these in Target Nodes lists.
[Figure] Select Active node View When select just a node from Available nodes list, you can create single node group.
[Figure] Single node Group View
Info Unlike failover group, Single node group does not support failover when failure occurs.
If you have selected single node cluster in installation step, only one node appears in Available Nodes list.
[Figure] Single Node Cluster View
Info Unlike failover group, Single node Cluster does not support failover when failure occurs.
Click Additional Settings to choose group mode as failover or parallel.
[Figure] Additional Settings View
Info
...
Failover group failover from active to standby node when failure occurs.
Parallel group is configured with the resources that can be executed on more than 2 nodes at the same time. Parallel group does not support failover, but restart the service when it is failed in local node.
- After completed Basic Settings, you can add resources to be monitored by wizard based.
[Figure] Initial Configuration Application View
각 리소스 추가 방법은 아래 링크를 참조 하십시오.
"7.4 복합 응용 리소스"에서 복합응용 추가 참조.
"7.3 기본 응용 리소스"에서 기본응용 추가 참조.
"7.7 원도우 서비스 리소스"에서 원도우 서비스 리소스 추가 참조. - If the added resource is incorrect, it can be deleted through clicking X.
To define the start or stop order among resources, use the arrow to change the order.
[Figure] Adding Service Resource View - After completed 'Configure Applications', you can add NIC and IP address resource.
If you would like to skip this step, check on 'Skip network configuration' and click 'Next' button.
[Figure] IP Resource and network Configuration View
[그림] 네트워크 구성 안함 옵션 체크 후 진행 화면 - To add NIC resource, select a NIC from drop down box of 'Select Network Adapter' and enter resource name.
Default value is same as name of NIC and you can edit as your definition.
[Figure] Network Adapter Select View To add IP resource, enter IP address which is represent for both nodes which is called Virtual IP address and enter resource name.
...
Default value is same as virtual IP address and you can edit as your definition.Warning NIC resource must be defined before add an IP resource.
[Figure] Adding iP Resource View- For more detail setting, click 'Additional Settings' and click 'OK' to complete 'Configure Network'.
[Figure] Additional setting View - After completed 'Configure Network', you can add disk resource.
[Figure] Initial Disk Configuration View
각 리소스 추가 방법은 아래 링크를 참조 하십시오.
"7.5 공유 디스크 리소스"에서 공유 디스크 리소스 추가 참조.
"7.9 스카시예약 리소스"에서 스카시예약 리소스 추가 참조.
"7.6 미러 디스크 리소스"에서 미러 디스크 리소스 추가 참조. - Mirror disk resource is added as below.
[Figure] Adding mirror disk resource is completed - After needed resource are all configured, MCCS will show suggested dependency map.
[Figure] Suggest dependency View - 의존성을 변경하고 싶다면 오른쪽 탭의 의존성 도구의 선택을 클릭합니다.
[Figure] Select Dependency View - Select the dependency line to be deleted, right click and select 'Unlink' to delete dependency between the resources.
[Figure] Deleting dependency view
- Click "OK" button and dependency will is deleted.
[Figure] Check to delete dependency - After deleting dependency, dependency line is disconnected.
[Figure] After deleting dependency view - To define dependency between the resources, select '↓Create Dependency' from 'Palette'.
[Figure] Create dependency view
- Click parent resource first and then click child resource.
[Figure] Create dependency view - This is message to check to create dependency.
[Figure] Check create dependency view - Dependency map is completed shown as below.
[Figure] After creating dependency view - After creating dependency, detailed information of group configuration can be shown as below.
[Figure] Group Detailed Information View - Summary of group creation result will appears after this is completed successfully.
[Figure] Group Creation is completed
Add Group Only
To add group only, and not resource, please follow the steps below.
- To add group, you can either click Cluster - Right click - Select Add Group or after clicking cluster, select Add Group button or select cluster from the tool bar and then click Add Group.
[Figure] Add resource group view - Enter group name, select the nodes from Available nodes list and click the '▶' button to moves these in Target Nodes lists.
[Figure] Select Active node View - In the application configuration step, do not configure application and click 'Next' button to continue.
[Figure] Configure application view - In the network configuration step, select 'Skip network configuration' and click 'Next' button to continue.
[Figure] Configure network view - In the disk configuration step, do not configure disk and click 'Next' button to continue.
[Figure] Disk configuration view
- In the configuration dependency step, since there is no configured resources, no information appears. Click 'Next' button to continue.
[Figure] Configure Dependency view - In the detail view, you will see added group information only.
[Figure] Detail information view - Click 'Finish' button and group is created.
[Figure] Group is created. - Click 'Close' button and you will see created group in the view.
[Figure] Group Creation Completed View
Deleting
To delete group, check the online state of the group first. If there are online group, the resources should be terminated or deleted.
- To delete group, select Select Group - Right Click - Delete Group.
[Figure] Delete Group View - If one or more than one of the resources is online state, a message shown below will appear.
When this happens, offline the group first before deleting it.
[Figure] Warning message of deleting group
- A warning window appears to confirm to delete group.
[Figure] Confirm delete group view If the mirror disk is included in the group, a message asking if replication program of mirror disk will be deleted as well.
Info if you click "OK" button, replication program is deleted as well. Press "Cancel" button if you do not wish to delete replication program.
[Figure] Deleting Mirror Disk View- This is the view after deleting group.
[Figure] After delete group View