Versions Compared

Old Version 1

changes.mady.by.user Copy Page Tree

Saved on

compared with

New Version 2

changes.mady.by.user 정은진

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Section


Column



Column
width350px


Panel

Table of Contents

Table of Contents
maxLevel4



...

  1. In the background, click on the MCCS link or open the web browser and access http://127.0.0.1:<UIPort>/main.


    [Figure] MCCS Shortcut Link

  2. When you access the link or URL, the following web console will be displayed. The initial password is set to 'password'. 

    [Figure] MCCS Web Console Access View

    Info


    Info

    You can change this port number in the Heartbeat Setting menu and pleaseplease, refer to 'Appendix F. Modify HeartBeat Configuration' of MCCS user guide "Chapter 12. Modify Heartbeat Configuration of MCCS Manual" about this.

    - ID : Account name to connect MCCS console. Default account is '"admin'".

    - Password : Default value is 'password'.- It is highly recommended that you change the default account and password. For more detail about editing these, please refer to 'Appendix E. Preferences of MCCS' of MCCS Windows User Guide.  한글 메뉴얼에는 없음"password".

    Info

    administrator Administrator : This account can all of control of the MCCS for group and resource like add, delete, switch, edit, setting dependency and etc.
    monitor Monitor : This account can only view the state of group and resources.


    Info

    You can change this in the Cluster Attributes View from Cluster Attributes tab and please, refer to '"Chapter 2. Management Web Console' Web Console of MCCS user guide Manual" about this.



  3. Press the [Login] button to start the initial heartbeat setting. 

...

  1. Enter cluster name as your definition and click on "Server Connection" to bring information of host identities. 
    Next step is unable to proceed if the network is not connected. 
    If there was an existing heartbeat configuration, its information will be remained.

    [Figure] Initial Heartbeat Settings

  2. Enter hostname or IP address of the node. Or enter 127.0.0.1 when you connect to local node.
    MCCS will brings and shows hostname and network informations for the node.
     
    [Figure] Server Connection

  3. Edit node name as your definition and select IP address for heartbeat and mirror network.

    Click

    'Test'

    the "Test" button to verify

    connectivities

    connectivity between two nodes.

    연결된 서버에 할당되어 있는 IP 주소가 나열되는 것을 확인할 수 있으며 사용할 IP 주소를 선택합니다. 
    핫빗을 설정한 후에 [테스트] 버튼을 클릭하여 연결확인을 합니다

    Info

    Default node name is host name of the node. Node name for clustering doest not must be identical to it's host name.
    MCCS requires at least a heartbeat interconnection, 3 interconnections is recommended.


    [Figure] Verifying connectivities between nodes


    한글메뉴얼 >>

    미러 라인은 복제 프로그램에서 사용될 데이터 복제 네트워크 입니다.
    미러 디스크 리소스를 사용하려면 3개의 핫빗으로 MCCS 구성을 권장합니다.
    Warning

    또한 미러 디스크 리소스를 포함한 MCCS 를 3개의 핫빗에서 2개의 핫빗으로 변경할 경우 정상적인 동작을 보장할 수 없습니다.영문 메뉴얼 >>
    Mirror network for data replication can be shared with one of primary heartbeat. Each pair of IP address of this between nodes must be on the same subnet.
    If these subnet are not matched between nodes,     'the "Test' " button for verification will not be enabled.
    When you use mirror disk resource, you can configure three heartbeats.
    It is highly recommended to configure the heartbeats at least three when you use mirror disk resource.


  4. Click 'the "Yes' " button, when you confirm for heartbeat configuration.

    [Figure] Applying Heartbeat configuration

  5. Click 'the "OK' " button to complete

    [Figure] Heartbeat configuration is completed  

...

  • Access the MCCS web console. Enter the user account and password. Default account is '"admin' " and password is '"password'". Click on Access to access the console.
  • Select Windows(W) ->Preferences> Preferences.

  • Click 'the "License Update' " button for each node in the '"License Information'".

     
    [Figure] Preferences View 

  • Enter a valid license key (temp. or perm.) for both nodes.
     
    [Figure] Entering an valid license key


    After heartbeat configuration and license update, you will create a Cluster Group and add a resource in this at next step.For more details about this, Please refer to ' "Chapter 5. Resource Group, Chapter 7. Resource' of 'MCCS User Guide' document" of "MCCS Manual" document.

    Warning

    ※ License Expire : Temporary license of MCCS is 90 days. It is required to issue new temporary or permanent license before temporary license expires.|
    If there is no license file or license expires after 15 days, MCCS works in restrict mode. So faults occures when MCCS does not failover.failo