...
| Section | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
SNMP
The Simple Network Management Protocol(SNMP) is an internet-standard protocol that devices can share information about their current state using a message format.
SNMP provides a standardized framework and a common language used for the monitoring and management of devices in a network.
MCCS supports SNMP(Simple Network Management Protocal) trap and can send an event message to a device in a network. It supports SNMP version 1, version 2c and version 3.
Configuring SNMP
You can add, edit, delete and view the SNMP configuration by select the node.
[Figure] Configuring SNMP
Adding SNMP
1) Select the 'Add' button in the bottom of the SNMP pane.
...
2) Select the SNMP version and click the 'OK' button.
[Figure] Selecting SNMP version
...
3) Select the security level in case of version 3 and click the 'OK' button.
[Figure] Selecting security level
[그림] version 3 보안형식 선택 화면
4) Enter the properties. If two or more values are entered, they will be separated by "," in destination IP.
[Figure] Entering properties
[그림] version 1, version 2c 속성 입력 화면
[Figure] Entering properties of security level level [Figure] Entering properties of security level level [Figure] Entering properties of security level
[그림] version 3 noAuthNoPriv 보안 형식 속성 입력 화면 [그림] version 3 authNoPriv 보안 형식 속성 입력 화면 [그림] version 3 authPriv 보안 형식 속성 입력 화면
Editing SNMP
Select the 'Edit' button in the bottom of the SNMP pane.
[Figure] Editing SNMP
Deleting SNMP
Select the 'Delete' button in the bottom of the SNMP pane.
...
[Figure] Warning message of deleting SNMP
Synchronizing the SNMP settings
When configuring of SNMP has complete, the properties are applied onto both nodes in the cluster.
But this will be only applied on the node when the peer node is isolated in the cluster. In this case, this can be synchronized by clicking the 'Sync' button.
[Figure] Synchronizing the SNMP settings.
...
[Figure] Warning message of synchronizing the SNMP
User account setting(Accounts)
You can edit, add and delete an user account.
User account screen
You can check an account at each node.
...
[Figure] User Account Setting
Admin edit screen
You can change the password and language for admin ID.
You cannot change the user roles.
...
Adding an account
1) Select 'the "Add user Account' " in the bottom of the add account "Account" screen.
[Figure] Adding Account in the User Account Setting
...
2) Enter the user ID, password, language, roles (Administrator/Monitor).
If you uncheck '"Add User Accounts for Every Node'", a new account will be set only for the current node in use.
...
[Figure] Finishing a Node Where User Account is Added
[Figure] Node Where User Account is Not Added
Modify the newly created account
You can modify the language and the user roles for this account.
You cannot change the user ID or password.
...
If different accounts are found at two nodes, you can unify them under the account on either node.
In addition, if the account file on one node is deleted, you can synchronize the account and retrieve it from the other node.
[Figure] User Account Synchronization
License information
Can check the status of license for each node.
...
[Figure] License Information
Logging
Can adjust the color for each log message level and select the range of log information.
[Figure] Logging Setting
Session information
At each node, you can check the access address/time and the user roles for the given ID.
...
[Figure] Session Information
UI
...
UI에 접속하는 접속 Port를 확인하고 수정할 수 있습니다.
사용자의 접속유지시간을 확인하고 수정할 수 있습니다.
관리자권한의 계정의 원격접속 허용을 확인하고 수정할 수 있습니다.
수동조작사유입력 기능 사용 여부를 확인하고 수정할 수 있습니다.
[그림] UI Config 화면
수동조작사유입력 기능을 활성화하면, 그룹 및 리소스의 제어시 다음 화면과 같이 조작 사유를 입력해야하며, 이 내용은 '수동조작 로그 보기'를 통해 확인 할 수 있습니다.
[그림] 수동조작 사유 입력 화면
[그림] 수동조작 로그 화면
기능 설정
현재 사용중인 기능을 확인하고 사용하지 않는 기능을 해제할 수 있습니다.
...
Config setting
It is available to check and modify information on the port to access to the UI.
And it also allows to check and modify how long a user had been being accessed that is shown as the session timeout item on the UI.
In addition, it is available to check and modify permission for an administrator's account to access from remote.
Checking and modifying function to memorize reason to operate manually are also provided by choosing either enable or disable.
[Figure] The UI Config setting View
It is necessary to input some reason to operate manually for controlling a group or resource such as the
following figure if activating the Enable to input reason to operate manually item, and it allows to check such things through the Logs related to manual operation item.
[Figure] The Reason to operate manually View
[Figure] The Logs related to manual operation View
Feature settings
It is available to check features which are being used currently and to disable useless features.
If you disable, it is unable to use relevant resources, moreover, there may be features you cannot disable because the relevant resources have been registered already.
[Figure] Feature Setting