...

Demotion

The transition from Primary role to Secondary role is called demotion.

bsradm secondary <resource>

Unmounting and demotion of resources entails switching the role to Secondary as the heaviest task among the command operations of bsr, and reflecting all data pending replication to the target side. This is the basic operation structure for matching data consistency between the replication source and the target. This operation ensures data consistency between the primary and secondary at the time of demoting. Therefore, in the process of unmounting and demoting, it is necessary to keep in mind a certain amount of latency that is required to reflect all pending data to the target.

...

manually fail-over

The procedure for manual transfer is as follows.

...

Stop all applications or services using the bsr device on the primary node, and demote the resource to secondary (after umounting the volume on Linux).

bsradm secondary <resource>

...

Demotion

The transition from Primary role to Secondary role is called demotion.

bsradm secondary <resource>

Unmounting and demotion of resources entails switching the role to Secondary as the heaviest task among the command operations of bsr, and reflecting all data pending replication to the target side. This is the basic operation structure for matching data consistency between the replication source and the target. This operation ensures data consistency between the primary and secondary at the time of demoting. Therefore, in the process of unmounting and demoting, it is necessary to keep in mind a certain amount of latency that is required to reflect all pending data to the target.

Resource down

You can stop the resource with the bsradm down command. down stops in the reverse order of the up process described above, and if the resource was in the promoted state, demotes first. In short, resource demotion, replication disconnection, volume detach, and resource release in the following order.

...

bsr provides various functions such as FastSync, checksum-based synchronization, truck-based synchronization, and bitmap clear synchronization for efficient synchronization.

Fast Synchronization

bsr has improved changed the existing full synchronization method that performs for the entire disk area to Fast Synchronization( FastSync), which synchronizes only the area used by the file system. bsr collects file system's usage area information for FastSync, records the usage area in OOS and performs synchronization.FastSync is applied at the time of For example, if you are only using 100MB on a 1TB disk, initial synchronization can be completed 10 times faster than the existing full synchronization (1TB) because only 100MB disk area is synchronized. FastSync operates at the following times.

• Initial full synchronization (bsradm primary --force

...

• )

• Manual full synchronization (invalidate/invalidate-remote

...

Checksum-based synchronization

Checksum data summarization can further improve the efficiency of bsr's synchronization algorithm. Checksum-based synchronization reads blocks before synchronization, obtains a hash summary of the contents on the current disk, and then reads the same sector from the other node and compares it with the obtained hash summary. If the hash match, the re-write for the block is omitted, and if they do not match, synchronization data is transmitted. This method can be advantageous in performance compared to the existing method of simply overwriting the block to be synchronized, and if the file system writes the same contents to the sector again while disconnected (disconnected), resynchronization is omitted for that sector. Overall, it have a more shorten synchronization time.

Truck-based synchronization

Truck-based synchronization by directly importing and configuring disks is suitable for the following situations.

• Initially, the amount of data to be synchronized is very large (hundreds of gigabytes or more)

• When the rate of change of the data to be copied is expected to be small compared to the huge data size

• When available network bandwidth between source and target sites is limited

In the above situation, if you do not synchronize by truck-based synchronization and initialize with the normal device synchronization method, it will take a very long time during synchronization.

Let's say one situation. There is a local node that has been disconnected from being in Primary. That is, the device configuration is complete and the same copy of bsr.conf exists on both nodes. Commands for initial resource promotion have been executed on the local node, but the remote node is not connected yet.

• Run the following command on the local node.

  Code Block
  bsradm new-current-uuid --clear-bitmap <resource>

• Create copies of the data to be replicated and the metadata of the data. For example, you could use a hot-swappable drive in the RAID-1 mirror. Of course, in this situation, the RAID set will need to be replaced with a new drive to continue mirroring. However, the disk drive you removed here is a literal copy that can be used elsewhere. If your local block device supports snapshot copy function, you can use it.

• Run the following command on the local node. There is no --clear-bitmap option in the second command run.

  Code Block
  bsradm new-current-uuid <resource>

• Configures the same copy of the original data to be physically taken directly for use on remote nodes.

• You can directly connect the disk physically, or you can copy the imported data to the existing disk and use it in bit units. This process should be done not only on the mirroring data, but also on the metadata. If such a procedure cannot be accepted, this method cannot proceed.

• Start the bsr resource on the remote node.

  Code Block
  bsradm up <resource>

When both nodes are connected, they will not initiate full device synchronization. Instead, only synchronization of blocks that have changed since the bsradm--clear-bitmap new-current-uuid command was invoked is automatically initiated.

If there is no change, there may be a simple synchronization depending on the area covered in the Activity Log rolled back from the new secondary node. 

Bitmap clear synchronization

You can use the option to clear the bitmap (--clear-bitmap) so that it can be quickly sync without an initial full synchronization over a long period of time. The following are examples of these operations.

It can be used to skip the initial sync by creating a new Current UUID and clearing the Bitmap UUID. This use case only works for the metadata just created.

1. On both nodes, initialize the meta and configure the device. bsradm -- --force create-md res

2. Start resources of both nodes and recognize each other's volume size at the time of initial handshake. bsradm up res

3. When both nodes are connected as Secondary / Secondary, Inconsistent / Inconsistent, create a new UUID and clear the bitmap. bsradm new-current-uuid --clear-bitmap res

4. Now both nodes are in Secondary / Secondary, UpToDate / UpToDate state, and promote one side to Primary to create a file system. bsradm primary res mkfs -t fs-type $(bsradm sh-dev res)

One obvious side effect of this approach is that the replica is full of old garbage (unless you make it the same using other methods), it is expected to find the number of unsynchronized blocks when online verification. This method should never be used in situations where the volume already has data. At first glance it may seem to work, but once you switch to another node, the data that was already there is not replicated, so the data is broken.

Adjust sync speed

When synchronization is in the background, the target data is temporarily inconsistent. This inconsistent state should be kept as short as possible, which is good in terms of consistency, so it is advantageous to have a sufficient synchronization speed. However, replication and synchronization share the same network band, and if the synchronization band is set high, relatively few replication bands can be provided. Lowering the replication bandwidth affects local I/O latency and consequently lowers local I/O performance of the active server. Because either side of replication or synchronization occupies a lot of bands unilaterally, it affects the operation of the other side relatively, so bsr implements variable-rate synchronization that adequately adjusts the synchronization band according to the replication situation while guaranteeing the replication band as much as possible. bsr use it as the default policy. Conversely, the fixed-rate synchronization policy is generally not recommended and should only be used in special situations, as it can lead to a decrease in local I/O performance when used during server operation in a way that ensures synchronization bands regardless of replication.

Fixed rate synchronization

The maximum bandwidth used for resynchronization in the background is determined by the resource's resync-rate option. These options are included in the disk section of the /etc/bsr.conf resource configuration as follows:

resource <resource> {
  disk {
    resync-rate 40M;  
    c-min-rate 40M;  
    c-plan-ahead 0;  
    ...
  }
  ...
}

The resync-rate and c-min-rate settings are specified in bytes per second. The default unit is Kibibyte, and the value of 4096 is interpreted as 4 MiB.

Variable rate synchronization

Fixed-rate synchronization is not an optimal method when multiple resources share a replication/synchronization network. Because they share the same network, if a synchronization rate is occupied for a specific replication resource channel, other resources are not guaranteed a fixed synchronization rate. In this case, you can mitigate that the synchronization rate is occupied by configuring to dynamically adjust the synchronization rate of each replication channel through variable rate synchronization. bsr determines the initial sync speed in this mode and then continuously adjusts the sync speed through an automatic control loop algorithm. This algorithm ensures sufficient bandwidth for foreground replication and greatly mitigates the impact of background synchronization on foreground I/O.

The optimal configuration for variable rate synchronization may vary depending on the available network bandwidth, application I/O pattern, and replication link congestion, and the optimal configuration setting may vary depending on whether replication accelerator(DRX) is used.

Congestion mode

In an environment where the replication bandwidth is variable (WAN replication environment), the replication link can sometimes become congested. Because of this, if the primary node's I/O waits, the performance of the local I/O will be degraded, which is undesirable. When detecting this congestion, you can configure it to suspend replication. Instead, in the situation where replication is interrupted, the primary data set is ahead of the secondary data, and these advanced data blocks are recorded as out-of-sync (OOS). when congestion is released, after all these oos is resolved through resynchronization. The following is an example of setting the congestion policy.

In the resource configuration file, the on-congestion option item sets the congestion mode, and the congestion-fill item sets the recognition threshold for congestion.

resource <resource> {
  net {
    sndbuf-size 20M;
    on-congestion pull-ahead;
    congestion-fill 2G;
    congestion-extents 2000;
    ...
  }
  ...
}

The pull-ahead option is used with congestion-fill and congestion-extents. The recommended values for congestion-fill are:

• When linking a replication accelerator(DRX), set it to about 90% of the DRX buffer size.

• If DRX is not linked, set to 90% of sndbuf-size.

• The recommended value for congestion-extents is 90% of the al-extents setting.

Disk flush

If the target node suddenly goes down due to power failure during replication, data loss may occur if the disk cache area is not backed up by a battery backup device (BBWC). In order to prevent this in advance, in the process of writing data to the disk of the target, after data is written to the media, the flush operation is always performed to prevent data loss.

The storage device equipped with BBWC does not need to perform the disk flush operation, so it provides an option to disable the flush as follows.

...

• )

• Online Verify check (bsradm verify)

Checksum-based synchronization

Checksum data summarization can further improve the efficiency of bsr's synchronization algorithm. Checksum-based synchronization reads blocks before synchronization, obtains a hash summary of the contents on the current disk, and then reads the same sector from the other node and compares it with the obtained hash summary. If the hash match, the re-write for the block is omitted, and if they do not match, synchronization data is transmitted. This method can be advantageous in performance compared to the existing method of simply overwriting the block to be synchronized, and if the file system writes the same contents to the sector again while disconnected (disconnected), resynchronization is omitted for that sector. Overall, it have a more shorten synchronization time.

Truck-based synchronization

Truck-based synchronization by directly importing and configuring disks is suitable for the following situations.

• Initially, the amount of data to be synchronized is very large (hundreds of gigabytes or more)

• When the rate of change of the data to be copied is expected to be small compared to the huge data size

• When available network bandwidth between source and target sites is limited

In the above situation, if you do not synchronize by truck-based synchronization and initialize with the normal device synchronization method, it will take a very long time during synchronization.

Let's say one situation. There is a local node that has been disconnected from being in Primary. That is, the device configuration is complete and the same copy of bsr.conf exists on both nodes. Commands for initial resource promotion have been executed on the local node, but the remote node is not connected yet.

• Run the following command on the local node.

  Code Block
  bsradm new-current-uuid --clear-bitmap <resource>

• Create copies of the data to be replicated and the metadata of the data. For example, you could use a hot-swappable drive in the RAID-1 mirror. Of course, in this situation, the RAID set will need to be replaced with a new drive to continue mirroring. However, the disk drive you removed here is a literal copy that can be used elsewhere. If your local block device supports snapshot copy function, you can use it.

• Run the following command on the local node. There is no --clear-bitmap option in the second command run.

  Code Block
  bsradm new-current-uuid <resource>

• Configures the same copy of the original data to be physically taken directly for use on remote nodes.

• You can directly connect the disk physically, or you can copy the imported data to the existing disk and use it in bit units. This process should be done not only on the mirroring data, but also on the metadata. If such a procedure cannot be accepted, this method cannot proceed.

• Start the bsr resource on the remote node.

  Code Block
  bsradm up <resource>

When both nodes are connected, they will not initiate full device synchronization. Instead, only synchronization of blocks that have changed since the bsradm--clear-bitmap new-current-uuid command was invoked is automatically initiated.

If there is no change, there may be a simple synchronization depending on the area covered in the Activity Log rolled back from the new secondary node. 

Bitmap clear synchronization

You can use the option to clear the bitmap (--clear-bitmap) so that it can be quickly sync without an initial full synchronization over a long period of time. The following are examples of these operations.

It can be used to skip the initial sync by creating a new Current UUID and clearing the Bitmap UUID. This use case only works for the metadata just created.

1. On both nodes, initialize the meta and configure the device. bsradm -- --force create-md res

2. Start resources of both nodes and recognize each other's volume size at the time of initial handshake. bsradm up res

3. When both nodes are connected as Secondary / Secondary, Inconsistent / Inconsistent, create a new UUID and clear the bitmap. bsradm new-current-uuid --clear-bitmap res

4. Now both nodes are in Secondary / Secondary, UpToDate / UpToDate state, and promote one side to Primary to create a file system. bsradm primary res mkfs -t fs-type $(bsradm sh-dev res)

One obvious side effect of this approach is that the replica is full of old garbage (unless you make it the same using other methods), it is expected to find the number of unsynchronized blocks when online verification. This method should never be used in situations where the volume already has data. At first glance it may seem to work, but once you switch to another node, the data that was already there is not replicated, so the data is broken.

Adjusting the synchronization speed

When synchronization is running in the background, the data on the target is temporarily in an inconsistent state. This inconsistent state should be kept as short as possible to ensure consistency, so it is beneficial to have a high enough synchronization rate. However, replication and synchronization share the same network band, and if the synchronization band is set high, replication will be given relatively little bandwidth. If the replication band is lowered, it will affect local I/O latency and result in local I/O performance degradation. If either replication or synchronization unilaterally occupies a lot of bandwidth, it will affect the behavior of the other, so we implement variable-band synchronization, which guarantees the replication band as much as possible while moderating the synchronization band according to the replication situation, and this is the default policy. In contrast, the fixed-band synchronization policy, which guarantees the synchronization band at all times regardless of replication, can cause local I/O performance degradation if used during server operation, so it is not generally recommended and should be used only in special situations.

Fixed rate synchronization

The maximum bandwidth used for resynchronization in the background is determined by the resource's resync-rate option. These options are included in the disk section of the /etc/bsr.conf resource configuration as follows:

resource <resource> {
  disk {
    resync-rate 40M;  
    c-min-rate 40M;  
    c-plan-ahead 0;  
    ...
  }
  ...
}

The resync-rate and c-min-rate settings are specified in bytes per second. The default unit is Kibibyte, and the value of 4096 is interpreted as 4 MiB.

Variable rate synchronization

Configuring with fixed-bandwidth synchronization is problematic for configurations where multiple resources share a replication/synchronization network. Because the resources share the same replication network, if the synchronization rate is occupied for a particular replication resource channel, the other resources are not guaranteed a fixed synchronization rate. In this case, variable bandwidth synchronization can be configured to dynamically adjust the synchronization rate of each replication channel to proactively adjust the synchronization band in response to other resources taking over. Variable-band synchronization determines an initial synchronization rate (by resync-rate) and then uses an automatic control algorithm to continuously adjust the synchronization rate. This algorithm ensures that the synchronization band is available from c-min-rate to c-max-rate while still allowing replication to operate on the front end. Setting c-max-rate too high will affect the replication band, so it is preferable to set it to match the network band.

The optimal configuration for variable bandwidth synchronization depends on the available network bandwidth, application I/O patterns, and replication link congestion, and the optimal configuration settings may vary depending on whether you are using Replication Accelerator (DRX).

Set the synchronization ratio

You can also set the synchronization rate as a percentage of the replication bandwidth.

resource <resource> {
  disk {
    c-min-rate 40M;  
    resync-ratio "3:1";
    ...
  }
  ...
}

You should disable device flushing only when running bsr on devices with battery backup write cache (BBWC). Most storage controllers automatically disable the write cache when the battery is exhausted and switch to write through mode when the battery is exhausted.

Consistency verification

Consistency verification is a function that performs replication traffic in real-time in block units during replication or compares block-by-block based on hash summaries to verify that the source and target data are completely matched in whole (used) disk volume units.

Traffic integrity check

bsr can use cryptographic message digest algorithms to verify message integrity between both nodes. When this function is used, bsr generates a message summary of all data blocks, delivers it to the other node, and verifies the integrity of the replication packet at the other node. If the summarized blocks do not match each other, retransmission is requested.

When replicating data, bsr can protect the source data against the following error conditions through this consistency check, and failure to respond to such situations can potentially cause data corruption during replication.

• Bit errors (bit flips) that occur in data transferred between main memory and the network interface of the transmitting node.

  • If the TCP checksum offload function provided by LAN Card is recently activated, hardware bitflip may not be detected by software.

• Bit errors that occur on data being transferred from the network interface to the receiving node's main memory (the same applies for TCP checksum offloading).

• Damage due to a bug or race condition within the network interface firmware or driver.

• Bit flips or random damage injected by the recombination network component between nodes (if not using direct connection, back-to-back connection).

Replication traffic consistency checking is disabled by default. To enable it, add the following to the resource configuration in /etc/bsr.conf.The example above sets the synchronization band to a ratio of 3 replication to 1 synchronization (4 total). However, the sync ratio is compared to the c-min-rate and if the c-min-rate is higher, it is applied as the c-min-rate value. This ensures that you have the minimum amount of synchronization bandwidth.

Congestion mode

In environments where the replication band is a variable band (WAN), the replication link can sometimes become congested. This causes the primary node's I/O to wait, resulting in a performance degradation of local I/O. Congestion mode is a configuration to respond to this situation.

When congestion is detected, replication is suspended and buffered data is slowly sent to the target while logging local I/O to OOS. During this process, the primary is in an Ahead data state compared to the secondary, and once it finishes sending buffered data, it automatically enters sync mode to synchronize the OOS areas that failed to replicate.

Here is an example of setting up a congestion policy

In the resource configuration file, set the congestion mode with the on-congestion option item and set the congestion detection threshold with the congestion-fill item.

resource <resource> {
  net {
    data-integrity-alg <algorithm>;sndbuf-size 1G;
    on-congestion pull-ahead;
    congestion-fill 900M;
    congestion-extents 5500;
    congestion-highwater 20000;
    ...
  }
  ...
}

<algorithm> is a message hashing compression algorithm supported by the kernel cryptography API in the system's kernel configuration. On Windows, only crc32c is supported.

After changing the resource configuration of both nodes identically, execute bsradm adjust <resource> on both nodes to apply the changes.

온라인 정합성 검사

온라인 정합성 검사는 장치 운영 중에 노드 간의 블록별 데이터의 정합성을 확인하는 기능입니다. 정합성 검사는 중복 검사하지 않으며 네트워크 대역폭을 효율적으로 사용하고 파일시스템에 의해 사용하고 있는 영역에 대해서 검사하는 것을 기본 동작으로 합니다.

온라인 정합성 검사는 한 쪽 노드에서(verification source) 특정 리소스 스토리지상의 모든 데이터 블럭을 순차적으로 암호화 요약(cryptographic digest)시키고, 요약된 내용을 상대 노드(verification target)로 전송하여 같은 블럭위치의 내용을 요약 비교 합니다. 만약 요약된 내용이 일치하지 않으면, 해당 블럭은 out-of-sync로 표시되고 나중에 동기화대상이 됩니다. 여기서 블럭의 전체 내용을 전송하는 것이 아니라 최소한의 요약본만 전송하기 때문에 네트워크 대역을 효과적으로 사용하게 됩니다.

리소스의 정합성을 검증하는 작업은 운영 중에 검사하기 때문에 온라인 검사와 복제가 동시에 수행될 경우 약간의 복제성능 저하가 있을 수 있습니다. 하지만 서비스를 중단할 필요가 없고 검사를 하거나 검사 후 동기화 과정 중에서 시스템의 다운 타임이 발생하지 않는 장점이 있습니다. 

보통 온라인 정합성 검사에 따른 작업은 OS에서 예약된 작업으로 등록하여 운영 I/O 부하가 적은 시간 대에 주기적으로 수행하는 것이 일반적인 사용법입니다.

활성화

온라인 정합성 검사는 기본적으로 비활성화되어 있는데, bsr.conf 내의 리소스 구성에 다음과 같은 내용을 추가하면 활성화할 수 있습니다.The pull-ahead option is used with congestion-fill, congestion-extents, or congestion-highwater. The recommended values for each property are as follows

• Set congestion-fill to approximately 90% of the size of sndbuf-size. If you are integrating a replication accelerator (DRX), set it to 90% of the DRX buffer. However, if the buffer is allocated a large size, say 10GB or more, the 90% threshold may be too large to detect congestion, so this should be adjusted to a reasonable value through tuning.

• The recommended value for congestion-extents is 90% of the al-extents setting.

• congestion-highwater detects congestion based on packet count. It is particularly appropriate for use in DR environments where capacity-based detection of replication congestion is not suitable. It is set to 20000 by default and is enabled by default. It is disabled when set to 0 and has a maximum value of 1000000.

Disk flush

If the target node suddenly goes down due to power failure during replication, data loss may occur if the disk cache area is not backed up by a battery backup device (BBWC). In order to prevent this in advance, in the process of writing data to the disk of the target, after data is written to the media, the flush operation is always performed to prevent data loss.

The storage device equipped with BBWC does not need to perform the disk flush operation, so it provides an option to disable the flush as follows.

resource <resource>
  disk {
    disk-flushes no;
    md-flushes no;
    ...
  }
  ...
}

You should disable device flushing only when running bsr on devices with battery backup write cache (BBWC). Most storage controllers automatically disable the write cache when the battery is exhausted and switch to write through mode when the battery is exhausted.

Consistency verification

Consistency verification is a function that performs replication traffic in real-time in block units during replication or compares block-by-block based on hash summaries to verify that the source and target data are completely matched in whole (used) disk volume units.

Traffic integrity check

bsr can use cryptographic message digest algorithms to verify message integrity between both nodes. When this function is used, bsr generates a message summary of all data blocks, delivers it to the other node, and verifies the integrity of the replication packet at the other node. If the summarized blocks do not match each other, retransmission is requested.

When replicating data, bsr can protect the source data against the following error conditions through this consistency check, and failure to respond to such situations can potentially cause data corruption during replication.

• Bit errors (bit flips) that occur in data transferred between main memory and the network interface of the transmitting node.

  • If the TCP checksum offload function provided by LAN Card is recently activated, hardware bitflip may not be detected by software.

• Bit errors that occur on data being transferred from the network interface to the receiving node's main memory (the same applies for TCP checksum offloading).

• Damage due to a bug or race condition within the network interface firmware or driver.

• Bit flips or random damage injected by the recombination network component between nodes (if not using direct connection, back-to-back connection).

Replication traffic consistency checking is disabled by default. To enable it, add the following to the resource configuration in /etc/bsr.conf.

resource <resource> {
  net {
    data-integrity-alg <algorithm>;
  }
  ...
}

<algorithm> is a message hashing compression algorithm supported by the kernel cryptography API in the system's kernel configuration. On Windows, only crc32c is supported.

After changing the resource configuration of both nodes identically, execute bsradm adjust <resource> on both nodes to apply the changes.

Online Verification

Online Verification is a function to check the consistency of block-specific data between nodes during service is online . it does not duplicate check, and it is basically used to efficiently use network bandwidth and check the area used by the file system.

The online verification sequentially encrypts all data blocks on a specific resource storage at one node (verification source), and then sends the summarized content to a verification target to summarize the contents of the same block location and compare it. If the summarized content does not match, the block is marked out-of-sync and is later synchronized. Here, network bandwidth is effectively used because only the smallest summary is transmitted, not the entire contents of the block.

Since the operation to verify the consistency of the resource is checked during operation, there may be a slight decrease in replication performance when online verification and replication are performed simultaneously. However, there is an advantage that there is no need to stop the service, and there is no downtime of the system during the scan or synchronization process after the scan.

Generally, it is common practice to perform tasks according to online verification as scheduled tasks in the OS and perform them periodically during periods of low operational I/O load.

Enable

Online verification is disabled by default, but can be activated by adding the following entry to the resource configuration in bsr.conf.

resource <resource> {
   net {
       verify-alg <algorithm>;
   }
   ...
}

algorithm means the message hashing algorithm, and only supports crc32c in Windows.

To enable online verification, make the same resource configuration changes on both nodes, then run bsradm adjust <resource> on both nodes to apply the changes.

OV run

After enabling online verification, you can run the test using the following command:

When an online verification is executed, bsr finds and displays the unsynchronized block in <resource> and records it. At this time, all applications that use the device can operate without any restrictions, and the role of the resource can also be changed.

The verify command performs a verification after changing the disk status to UpToDate. Therefore, it is desirable to perform UpToDate on the replication source node side after the initial sync is completed. For example, if you perform verification on the disk node side of the Inconsistent state, the disk state is changed to UpToDate, which may cause operational problems.

If an out-of-sync block is detected while verification is running, after verification is complete, you can synchronize with the next command. At this time, the direction of synchronization is from the primary node to the secondary direction, and synchronization is not performed in the secondary/secondary state. Therefore, in order to solve the OOS due to online verification, promotion to the primary on the source side node is required. 

drbdadm disconnect <resource>
drbdadm connect <resource>

Automatic verification

If you need to do a regularity check, register the bsradm verify <resource> command to the task scheduler in the following way.

First, create a script file with the following contents in a specific location on one of the nodes.

To verify all resources, you can use the all keyword instead of <resource>.

The following is an example of creating a scheduled task using schtasks (windows schedule setting command). With the following settings, online verification is performed every Sunday at 00:42 AM.

 schtasks /create /tn "drbd_verify" /tr "%wdrbd_path%\verify.bat" /sc WEEKLY /D sun /st 00:42

Persist Role

While resource roles can be changed based on operational circumstances, sometimes you may want to persist roles. (BSR 1.7.3 and later)
A resource with persist-role set will continue to have the resource role explicitly specified (with the bsradm command) at the time of restart. This works in any situation where the replication service or system reboots, causing the resource to restart.

resource <resource> {
    net options {
       verify-alg <algorithm>    persist-role yes;
     }
   ...
}

algorithm 은 메시지 해싱 알고리즘을 말하며 Windows 에선 crc32c 만 지원합니다.

온라인 검증을 활성화 하기 위해 양 노드의 리소스 구성을 똑같이 변경한 후, 양 노드에서 bsradm adjust <resource>를 실행하여 변경사항을 적용시킵니다.

온라인 정합성 검사 실행

온라인 정합성 검사를 활성화한 후, 다음 명령을 사용하여 검사를 실행할 수 있습니다.

온라인 검사가 실행되면, bsr 은 <resource>에서 동기화되지 않은 블록을 알아내 표시하고 이를 기록합니다. 이때 디바이스를 사용하는 모든 응용 프로그램은 아무런 제약 없이 동작할 수 있으며, 리소스의 역할 변경도 가능합니다.

verify 명령은 디스크 상태를 UpToDate로 변경한 후 검증을 수행합니다. 따라서 초기싱크가 완료된 이후 UpToDate 인 복제 소스 노드 측에서 수행하는 것이 바람직 합니다. 예를 들어, Inconsistent 상태의 디스크 노드 측에서 verify를 수행하면 디스크 상태가 UpToDate로 변경 되어 운영 상 문제가 될 수 있으므로 주의가 필요합니다.

검증이 실행되는 동안 out-of-sync 블록이 감지되면, 검증이 완료된 후에 다음 명령으로 동기화할 수 있습니다. 이 때 동기화가 되는 방향은 Primary 노드에서 Secondary 방향으로 이루어지며 Secondary/Secondary 상태에서는 동기화를 진행하지 않습니다. 따라서 Online 검증에 따른 OOS를 해소하기 위해선 소스 측 노드에 대한 Primary로의 승격이 요구됩니다. 

drbdadm disconnect <resource>
drbdadm connect <resource>

자동 검사

정기적으로 정합성 검사를 할 필요가 있다면, 다음과 같은 방법으로 bsradm verify <resource> 명령을 작업 스케줄러에 등록합니다.

우선 노드 중 하나에서 특정 위치에 다음과 같은 내용의 스크립트 파일을 만듭니다. 

모든 리소스를 검증하려면 <resource> 대신 all 키워드를 사용하면 됩니다. 

다음은 schtasks(windows 스케줄 설정 명령어)를 사용해 예약된 작업을 생성하는 예 입니다. 다음과 같이 설정 하면 매주 일요일 자정 42분에 온라인 정합성 검사를 수행하게 됩니다.

...

  ...
}

One-way replication

If you always want to have only one-way replication from the primary node to the standby node, without swtichover or failover, consider the target-only attribute on the standby node side. (BSR 1.7.3 and later)

• Set the persist-role attribute described above in the resource options section to fix the roles of the primary and standby nodes.

• Set the target-only attribute on the standby node side to force the replication/synchronization direction from the primary node to the standby node only.

A target-only node is prohibited from acting as a source in all replication/sync operations, including explicit commands, and can only have a target role; any manual synchronization or promotion commands that act as a source are blocked (but promotion is allowed on disconnection).

resource <resource> {
  options {
    persist-role yes;
  }
  
  on active {
    ...
  }
  
  on standby-DR {
    ...
    options {
      target-only yes;
      ...
    }
  }
  ...
}