Versions Compared

Version Old Version 14 New Version Current
Changes made by

이진현

이진현

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

A response to writing on the mirror volume disk is immediately sent after the source volume is saved. Since it does not wait until data is sent to the target volume and saved there, the response time is very fast. However, in case of trouble, it can cause data mismatches due to data failed to be transmitted at that time.

...

  1. Select the group -> Right click with the mouse -> Add the resource.   
  2. In resource wizard, select a shared disk DR and click the Next button. 

  3. The shared volume set of resource wizard will display the drive characters that can be used to compose the shared disk DR and the existing drive characters that are already configured.
    You cannot inquire about information at the remote server. So, you need to enter IP addresses on your own. 

    Warning

    The drive characters letter to be used as the shared disk DR should be same on the both servers that compose nodes in a cluster. Data will be copied replicated to the target node off-site DR node(Remote server) from the source node. The remote server cannot be the source. Be careful when you select the drive character letter where data exists in the remote server, the data will be overwritten when mirror set in completed. If you try to add the an existing mirror volumedisk between shared disk set and remote disk, <mirrored> will be added follwoed to the volume driver letter of shared disk.



      [Figure] Shared Disk DR Resource Added


  4. Click the 'Additional Setup' to define the synch mode and the disk test option.

    Info

    <Sync mode> Once selected, the sync mode cannot be reversed. So, be careful.
    Sync mode : Response is slow but there is no data loss involved. Async mode : Relatively faster than the sync mode but it can suffer from data loss.
    <Disk test option> Set the disk test command option. For more details on the function, refer to MSDN.

     
     [Figure] Shared Disk DR Additional Setting


  5. Press the Finish button after adding the shared disk DR resource, the following warning screen will be displayed.
    Check again if it is the correct source server selected.
    If not, then click on the 'Cancel' button and set it again. 


    [Figure] The warning screen displayed when you press the Finish button after adding the shared disk DR resource   
     

  6. Click the 'Finish' button to add the shared disk DR resource. You can immediately check the result in the management web console.

...

Status

Agent's functions

Description

Note

Online

In this status, you can access the source volume and perform a writing test properly.

 

Offline

Regardless of the mirror role, the LOCKVOLUME command is used to lock the volume. If the mirror volume disk is not defined, the LOCKVOLUME command is ignored and regarded as a failure.

 

Monitoring

Before monitoring, update the status of resource first. Perform a disk write test to determine the status of resource.
If the writing test is successful, it is regarded as the online state. If the writing test failed on the disk, it is regarded as the offline state.

 

Offline

Except for the online and trouble states, it is always offline.

 

Online

Type of operation is determined by the role of the mirror volume disk at the start node.
<Source volume> 1. You can unlock and write the volume. 2.To unlock, you can use the 'UNLOCKVOLUME' menu in the copy program. Check whether there are dirty bits.
<Target or NONE volume> 1. If the mirror role is target or NONE volume, run the SWITCHOVERVOLUME command.

 

Monitoring

Refer to the description of monitoring as above.

 

Fault


If a writing test failed online, or an attempt to go online is failed, the trouble state is displayed.
*Failover deactivation state When a mirror network communication failure, target node or target disk failure occurs, the mirror state is changed from 'MIRRORING' to other, such as 'MIRROR_PAUSED'. If the mirror status is not 'MIRRORING', a failover will take place and it can cause data losses or damages. To prevent this problem, an agent deactivates the failover mode if the mirror status is not "MIRRORING". If the failover mode is deactivated, no failover will take place even if manual failover or troubles occur. If mirror network communication failures are recovered, and communication resumes, it will automatically perform RESYNChas been failed and then, recovered as normal, mirror status is changed to RESYNC and data re-synching is initiated between primary cluster set and off-site DR node. When the mirror status is changed to MIRRORING, the failover mode will be also automatically activated.

 

Online

Refer to the above online command.

 

Offline

Regardless of the mirror role, the LOCKVOLUME command is used to lock the volume. If the mirror volume disk is not defined, the LOCKVOLUME command is ignored and regarded as a failure.

 

...

ArgList Factor

Description

Type

Default

Modification

Note

ChkDsk

When the volume is mounted, according to the 'Disk Test Options', disk is tested for errors. If it is set to true, and if dirty bits are set to the online volume, the ChkdskArg option will be used to run checkdisk. Before running checkdisk, the mirror copying will be automatically stopped and resynchronization will be performed after finished.

BOOLEAN

false

O

 

ChkdskArg

When the checkdisk (Chkdsk) option is set to true, the check disk command option is activated.

STRING

/F

O

 

DirtyBit

It means that dirty bits are set to the target mirror volumedisk. In general, if you need to check the integrity of the target volume, the system will set this.

BOOLEAN

false

X

 

DriveLetter

The mirror volume disk is assigned to the drive characterletter. It should be configured to obtain the same value at the source and the target systems.

STRING

 

X

 

DRState

The mirror status of the mirror volumedisk. It is renewed from an event log.

STRING

 

X

 

DRType

Determine the mirror synchronization mode. Set it to A or S. ( A - async mode, S - sync mode) * If it is set to asynch mode, data loss can occur.

STRING

A

X

 

ResyncNeed

It represents the total sum of the blocks requiring re-synchronizing.

INTEGER

 

X

 

ResyncTotal

It is the total sum of the re-synchronizing blocks.

INTEGER

 

X

 

SharedSrcIp

It is the IP address used to manage the volume shared between two nodes.

STRING

 

X

 

SharedSrcRole

It represents shows the role of the shared volume disk for each node.

STRING

 

X

 

TargetDRIp

The IP address used to copy the volumeIt is IP address of off-site DR node for mirror disk.

IP ADDRESS

 

X

 

TargetDRLetter

It is the drive character for the DR target volumea driver letter using mirror disk of off-site DR node.

STRING

 

X

 

TargetDRRole

It represents shows the role of the shared volume for the target of mirror disk of off-site DR node.

STRING

 

X

 

TotalSpace

It represents the total size of the target mirror volumedisk.

INTEGER

 

X

 

UsedSpace

It represents the available size of the target mirror volumedisk.

INTEGER

 

X

 

Attribute value of ArgList arguments are the values that are added resources and the value can be changed or viewed through ’Specified Attribute’ list on the detailed information panel.