Versions Compared

Version Old Version 23 New Version Current
Changes made by

환기장

정은진

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Section
Column

It monitors the physical network devices mounted in the system.
To obtain a network address, the network device resource should operate properly and it is also necessary to periodically monitor them.
To differentiate individual network devices in a system where multiple network cards are installed, we use the name registered in the MAC address or device driver, or the name registered in the network connection registration information.
A network card agent uses the name (FriendlyName) registered in the network connection registration information.
This name is a unique name that is familiar to a general user. It can be easily modified for user's convenience. The adapter name appearing in the 'Network Connection' screen, or the information displayed after 'Ethernet Adapter' when you run the 'ipconfig' command in the command prompt is the name used to identify a network card. The network interface card(NIC) resource defines this name by using the AdapterName attribute. 

Column
width350px
Panel

Table of Contents

Table of Contents
maxLevel4

 

 

 

 


Info

네트워크 카드 이름은 공백 또는 특수 문자 사용을 자제해 주십시오Do not use space or special characters when designating a network card name.

Adding

네트워크 카드 리소스를 그룹에 추가합니다.
네트워크 카드 리소스는 그룹에 추가시 바로 활성화 되고, 온라인으로 표시 됩니다.Add the network card resource to a group.
When you add the network card resource to a group, it will be immediately activated and displayed as online. 

  1. Select a group → right click → 'Add Resource'.

  2. Select 'NIC' from Resource Type lists and click 'Next' button. 

  3. Enter resource name and select NIC.

    [Figure] Add network card wizard view

  4. Click on the Add Setting button to enter the ping timeout and the test address list.

    Info

    Additional setting can be selected as an option. You don't need to enter it.
    테스트 주소 목록은 ','로 구분하여 여러개 지정 가능합니다.  Multiple test addresses are separated by ",". 

     
     [Figure] Additional Settings of NIC resource

    완료 버튼을 클릭하면 네트워크카드 리소스가 추가 되며, 
     관리 웹 콘솔 상에서 바로 확인이 가능합니다.

Deleting

...


  2. Click the 'Finish' button to add the network card resource.
    You can immediately check the result in the management web console.

Deleting

Select the resource. -> Right click with the mouse. -> Delete the resource.
The deleted resource will immediately disappear from the management web console.

Status

 

The following table explains the status switching of the MCCS resource caused by a user's command and the status.
The command assumes that it is generated by a user.

Network card agent: Manages the physical network adapters.

...

MCCS cannot use the online/offline commands to a network device. It is because a network is managed by the OS as soon as it is installed in the H/W.
Due to the characteristics, a network card's resource type action attribute is set to none. Also, its NoAction value is set to true.
The attribute value cannot be used to start or terminate the resource. It is operable at all nodes at the same time but it only monitors the status. It is called a monitoring only resource.


 

Attribute

네트워크 카드 리소스의 고유 속성을 표시 합니다Show the unique attribute of network card resource.

Attribute

Description

Type

DefaultEditNote

AdapterName

It is the ethernet adapter name registered in network interface card.

STRING

 O 

PingTimeout

It is the time limit for ping test.
It goes through the test with the IP registered in TestAddressList and if there is no IP, it is ignored.

INTEGER

2 secO 

TestAddressList

It is the list of network access test address. If the ICMP test succeeds in at least one address, network connection state is considered normal. When there is more than one address, they are separated by ",".

IP ADDRESS

 O 

...