CLI is the function to send a command to the MCCS service in the system's command window.
MCCS CLI is the function to send a command to the MCCS service in the system's command window mode.
MCCS provides the following types of CLI: mclog to add arbitrary log, mcgroup to command a group, and mcres to command the resource group.
In general, CLI prepares scripts (*.sh and etc) to send various commands to the MCCS service.
CLI is located in $MCCS_HOME\bin.

MCCS 는 설치시 최초 사용자 계정으로 id 가 When you install MCCS, the initial user account ID is set to 'admin' 암호가 and the password is set to 'password'인 계정을 생성합니다.
CLI 명령을 실행시 id 와 password를 입력하지 않으면 , 위의 최초 사용자 계정의 id와 암호로 실행됩니다.
따라서 최초 사용자의 패스워드 변경시, 필수적으로 CLI 명령에 id와 password를 옵션으로 입력해야만 합니다.

When you run the CLI command, you need to enter the ID and the password. Otherwise, the above initial ID and password will be used.
Thus, when you change the initial user password, you must enter the ID/password in the CLI command as options.

#!/bin/bash
# CLITestGroupCreate 그룹이a 없다면new 신규 그룹을 생성합니다.
group
mclog="$MCCS_HOME/bin/mclog"
mcgroup="$MCCS_HOME/bin/mcgroup"
$mclog -n 192.168.100.2 -p 4321 -s CLITestGroup -l INFO -m "Start CLI 테스트Test 코드를 실행합니다Code."

end
{
	$mclog -n 192.168.100.2 -p 4321 -s CLITestGroup -l INFO -m "Stop CLI 테스트 코드를 종료합니다.Test Code"
}
$mcgroup -state CLITestGroup
if [ $? -ne 0 ]
then
	end
fi
# CLITestGroup을Create 생성합니다CLITestGroup.
$mclog -n 192.168.100.2 -p 4321 -s CLITestGroup -l INFO -m "CLITestGroup이 존재 하지 않아 그룹을 생성합니다Creat new group since CLITestGroup does not exist."
$mcgroup -add CLITestGroup
$mcgroup -modify CLITestGroup -a TargetNodeList Beta,Alpha
$mclog -n 192.168.100.2 -p 4321 -s CLITestGroup -l INFO -m "CLITestGroup을 생성했습니다."

CLITestGroup is created"

#/bin/bash
# CLITestProcess를 시작합니다. 
mclog="$MCCS_HOME/bin/mclog" 
mcres="$MCCS_HOME/bin/mcres" 

$mclog -n 192.168.100.2 -p 4321 -s CLITestProcess -l INFO -m "Start CLI 테스트Test 코드를 실행합니다Code."

# CLITestProcess가 Test 있는지if 검사합니다.CLITestProcess exist
$mcres -list CLITestProcess
if [ $? -ne 0 ]
then
	end 
else
	cliTestProcessCreat
fi

cliTestProcessCreat
{
	# CLITestProcess  After 리소스를creating 생성한a 후에resource, 활성화enable 시킵니다it.

	$mclog -n 192.168.100.2 -p 4321 -s CLITestProcess -l INFO -m "Create and cause CLITestProcess 리소스를resource 생성하고go 온라인 시킵니다online."


	$mcres -add CLITestProcess -t Process -g CLITestGroup 
	$mcres -modify CLITestProcess -a Path /usr/local/testprocess
	$mcres -modify CLITestProcess -a InteractWithDesktop true
	$mcres -enable CLITestProcess
	$mcres -online CLITestProcess -n Beta
}
end
{
	# 그룹Monitors 상태를group 모니터링 합니다state.

	$mclog -n 192.168.100.2 -p 4321 -s CLITestGroup -l INFO -m "Terminates CLI 테스트Test 코드를 종료합니다Code."
	mclog -n 192.168.100.2 -p 4321 -s cli -l ERROR -m "mclog test message"
}