Table of Contents

Installation

Insert Installation Media

To install MCCS, Please insert MCCS CD Media disk into the CD-ROM.
Open CD-ROM drive and execute installer.
MCCS Installation file is different by OS version.

 You must have administrative privileges to intall the MCCS. The installation will be terminated due to lack of required permissions with non-administrative user.

 

For 32 bit

For 64 bit

Language Selection

When execute installer a dialog box of 'Choose Setup Language' appears as below.
Selected language will be used as the primary language of MCCS.

[Figure] Language Selection Screen


Start Installation

 

This is the initial setup window of MCCS installation wizard.
Click [Next] to proceed to the next step.

[Figure] MCCS Initial Installation View


License Agreement View

It shows license agreement of the product. 
You must accept the agree to proceed installation. 

[Figure] MCCS License Agreement


Folder Selection

Select a folder to install MCCS.
Click [Browse] to select other installation folder.

[Figure] MCCS Folder Selection


If MCCS was installed and/or deleted before in the past, a warning message will be prompt as shown below asking if you would like to install MCCS in the same folder.
It is recommended to install in the same folder.

[Figure] MCCS Existing Folder Selection Screen


Start Menu Group Selection

Select start menu group of MCCS.
To configure start menu for user only, do not check on 'Create Short Cut to all users'.

[Figure] MCCS Start Menu Group Selection

 

Firewall Setting

Firewall setting is done automatically.

 

SingleNodeCluster Setup

SingleNodeCluster Setup can be selected. 

A single node cluster is a cluster made of a single node.
Do not check the setting page when you configure MCCS by using a two node cluster.


SingleNodeCluster Setup does not require any other settings to run MCCS in a node.

 

[Figure] MCCS SingleNodeCluster config View


Software component selection

When install MCCS, you can choose to install redundancy program or data replication program. 

Mirror disk feature isn't included in redundancy program.
You must install data replication program to support mirror disk.

[Figure] Selection of SW component


Web console access port setting

Set the web console access port (UIPort).  The configured web console is used to access the MCCS web console by using a web browser.
Default port is 10080. 

[Figure] MCCS UIPort Setting


Start Installation

[Figure] Start MCCS Installation View


Finish Installation and Enter License key

You will see a view to enter license key when installation is finished. 
Enter the license key.

※ License Expire : Temporary license of MCCS is 90 days.
It is required to issue new temporary or permanent license before temporary license expires. 
If there is no license file or license expires after 15 days, MCCS works restrict mode. So faults are occured MCCS does not failover.

 

[Figure] Entering license key


If the license is incorrect, warning message appears as shown below.
MCCS License is invalid

[Figure] MCCS License is not valid view


Expiration date will be shown if the temporary licenses are valid.

[Figure] After inserting license view


No information is shown if the license is not entered. 

[Figure] License not inserted View


You will see a message that system needs to be rebooted when install data replication program. 

[Figure]  Reboot System View

 

When it finishes rebooting, MCCS installation will be finished.

 

 

Check Installation

When the installation is finished successfully, in the background, a shortcut icon to the MCCS web console will be created and there will be the 'MCCS' folder in 'Program' of the 'Start' menu.

[Figure] MCCS Folder Screen


Subfolders Basically Installed in the MCCS Folder

Language Change

Language that is set during initial installation (Refer to "Language Selection") is the language that is used.
To change the language, please follows these steps on both servers.

  1. Close the web console.
  2. Terminate the 'MCCS Agent' service in Window service of the both nodes.
  3. At the both nodes, open the MccsServer.ini (file location: %MCCS_HOME%\bin\) file and switch to the new language as follows and save it. 
    If you change the language in the mccsserver.ini file, the log output will be generated in that language. 
    If you want to change the language for the web console, refer to "MCCS User Manual: Appendix E. Environment Setting".
  4. In Window service of the both nodes, start the 'MCCS Agent' service.
  5. After accessing the MCCS web console, check the changes made.