| Section | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Installation
Install by Web Console
To install install MCCS, Please insert MCCS CD Media disk into the CD-ROM.a
Open CD-ROM drive and execute installer.
MCCS Installation file is different by OS version.
| Info | ||
|---|---|---|
| ||
You must have root privileges to install the MCCS. |
Both of 32 bit, 64 bit file is executed by as root user.
- MCCS_linux_4.sh
Language Selection
When execute When execute installer a dialog box of 'Choose Setup Language' appears as appears as below.
elected language will be used as the primary language of MCCS.
[Figure] Language Selection Screen
Start Installation
This is the initial setup window of MCCS installation wizard.
Click [Next] to proceed to the next step.
[Figure] MCCS Installation View
License Agreement View
It shows license of the product.
You must agree the license to proceed installation.
[그림Figure] MCCS 라이선스 동의 화면Agreeing to the MCCS License
Directory Selection
Select a directory to install MCCS.
Click [Browse] to select other installation directory.
[Figure] MCCS Directory Selection
If MCCS was installed and/or deleted before in the past, a warning message will be prompt as shown below asking if you would like to install MCCS in the same directory.
It is recommended to install in the same directory.
[Figure] MCCS Existing Directory Selection Screen
JRE Directory Selection for MCCS (Setting view appears only when PowerLinux is installed.)
Select the folder where JRE is installed. Click Click Browse to select other JRE folder.
[Figure] Select MCCS JRE View
Firewall Setting
Firewall setting is done automatically.
SingleNodeCluster Setup
SingleNodeCluster can be selected here.
| Info |
|---|
A single node cluster is a cluster made of a single node. |
SingleNodeCluster Setup does Setup does not require any other settings to run MCCS in a node.
[Figure] MCCS SingleNodeCluster Setting view
웹 콘솔 접속 포트 설정
...
...
Web console access port setting
Set the web console access port (UIPort)를 설정합니다. 설정된 웹 콘솔은 웹 브라우저로 MCCS 웹 콘솔에 접속하기 위해 사용됩니다.
기본 포트는 10080 이 됩니다.
[그림] MCCS UIPort 설정 화면The configured web console is used to access the MCCS web console by using a web browser.
Default port is 10080.
[Figure] MCCS UIPort Setting
Start Installation
[Figure] Start MCCS Installation view
Finish Installation and Enter License key
You will see a view to insert license when installation is finished.
Enter the license key.
| Warning |
|---|
※ License Expire : Temporary license of MCCS is 90 days. It is required to issue new temporary or permanent license before temporary license expires. |
[Figure] Insert MCCS License view
If the license is not entered correctly, a warning message as below will appeared be as 'MCCS license is not valid'.
[Figure] Warning message about invalid key
When license is entered correctly, information as below will be appeared.
[Figure] After inserting license view
라이선스를 입력하지 않으면 아무런 정보도 출력되지 않습니다.
If you don't enter the license information, nothing will be displayed.
[Figure] License not inserted View
Click "Finish" button and MCCS installation is completed.
Install by CLI
| Expand | ||
|---|---|---|
| ||
Set authority in installation file.
Execute installation file.
Install Program and select language.
This is license agreement view.
Specify installation location.
Select whether to have SingleNodeCluster.
Set UIPort.
Start installing MCCS.
Insert license view.
Installation completed view
|
Confirm Installation
- bin
Programs that start/run MCCS. - config
Program configuration files created during installation and operation. - jre
Files related to 'Java runtime environment'. - logs
MCCS log files are saved in this folder.
Language Change
Language that is set during initial installation (Refer to "Language Selection") is the language that is used.
To change the language, please follows these steps on both servers.
Close the web console.
Using the following command, terminate the MCCS service for the both nodes.
Info 서비스 중지 및 시작은 반드시 root 사용자로 실행해야 합니다When you start or stop the service, you must use the root user role.
Code Block title Stop MCCS Service service mccs_agent stop
- At the both nodes, open the MccsServer.ini (file location: $MCCS_HOME\bin\) file and switch to the new language as follows and save it.
If you change the language in the mccsserver.ini file, the log output will be generated in that language.
If you want to change the language for the web console, refer to "MCCS User Manual: Appendix E. Environment Setting".- Korean → ko
- English → en
- Chinese → zh_CN
[그림Figure] Language Change in the mccsserver.ini 파일의 언어 변경 화면file
Using the following command, start the MCCS service for the both nodes.
Code Block title Start MCCS Service service mccs_agent start
- After After accessing the MCCS web console, check the changes made.