Skip to end of metadata
Go to start of metadata

You are viewing an old version of this content. View the current version.

Compare with Current View Version History

« Previous Version 19 Next »

 

 이 페이지의 주요 내용

Installation

Install by Web Console

To install MCCS, Please insert MCCS CD Media disk into the CD-ROM.a
Open CD-ROM drive and execute installer.
MCCS Installation file is different by OS version.

 

Warning

You must have root privileges to install the MCCS.
The installation will be terminated due to lack of required permissions with non-root user.


Both of 32 bit, 64 bit file is executed by as root user.

  • MCCS_linux_4.sh

Language Selection

When execute installer a dialog box of 'Choose Setup Language' appears as below. 
elected language will be used as the primary language of MCCS.


[Figure] Language Selection Screen


Start Installation

This is the initial setup window of MCCS installation wizard.
Click [Next] to proceed to the next step.

[Figure] MCCS Installation View


License Agreement View

It shows license of the product. 
You must agree the license to proceed installation. 

[그림] MCCS 라이선스 동의 화면


Directory Selection

Select a directory to install MCCS.
Click [Browse] to select other installation directory.


[Figure] MCCS Directory Selection


If MCCS was installed and/or deleted before in the past, a warning message will be prompt as shown below asking if you would like to install MCCS in the same directory.
It is recommended to install in the same directory.


[Figure] MCCS Existing Directory Selection Screen


JRE Directory Selection for MCCS (Setting view appears only when PowerLinux is installed.)

Select the folder where JRE is installed. Click Browse to select other JRE folder. 

[Figure] Select MCCS JRE View


Firewall Setting

Firewall setting is done automatically.


SingleNodeCluster Setup

SingleNodeCluster can be selected here.

A single node cluster is a cluster made of a single node.
투노드 클러스터로 MCCS를 구성 할 시에는 설정페이지에 체크하지 마십시오. 


SingleNodeCluster Setup does not require any other settings to run MCCS in a node.

[Figure] MCCS SingleNodeCluster Setting view


웹 콘솔 접속 포트 설정

웹 콘솔 접속 포트(UIPort)를 설정합니다.  설정된 웹 콘솔은 웹 브라우저로 MCCS 웹 콘솔에 접속하기 위해 사용됩니다.
기본 포트는 10080 이 됩니다. 

[그림] MCCS UIPort 설정 화면


Start Installation

[Figure] Start MCCS Installation view


Finish Installation and Enter License key

You will see a view to insert license when installation is finished. 
Enter the license key.

※ License Expire : Temporary license of MCCS is 90 days. It is required to issue new temporary or permanent license before temporary license expires.
If there is no license file or license expires after 15 days, MCCS works restrict mode. So faults are occured MCCS does not failover.

[Figure] Insert MCCS License view


If the license is not entered correctly, a warning message as below will appeared be as 'MCCS license is not valid'.


[Figure] Warning message about invalid key


When license is entered correctly, information as below will be appeared. 

[Figure] After inserting license view


라이선스를 입력하지 않으면 아무런 정보도 출력되지 않습니다.

[Figure] License not inserted View


Click "Finish" button and MCCS installation is completed. 

Install by CLI

 CLI

Set authority in installation file.

Execute installation file.

Install Program and select language.

This is license agreement view.

Specify installation location.

Select whether to have SingleNodeCluster.

Set UIPort.

Start installing MCCS.

Insert license view.

Installation completed view

Confirm Installation

  • bin
    Programs that start/run MCCS.
  • config
    Program configuration files created during installation and operation.
  • jre
    Files related to 'Java runtime environment'.
  • logs 
    MCCS log files are saved in this folder.

Language Change

Language that is set during initial installation (Refer to "Language Selection") is the language that is used.
To change the language, please follows these steps on both servers.

  1. Close the web console. 

  2. Using the following command, terminate the MCCS service for the both nodes.

    서비스 중지 및 시작은 반드시 root 사용자로 실행해야 합니다.

    Stop MCCS Service
     service mccs_agent stop
  3. At the both nodes, open the MccsServer.ini (file location: $MCCS_HOME\bin\) file and switch to the new language as follows and save it.
    If you change the language in the mccsserver.ini file, the log output will be generated in that language. 
    If you want to change the language for the web console, refer to "MCCS User Manual: Appendix E. Environment Setting".
    • Korean → ko
    • English → en
    • Chinese → zh_CN

      [그림] mccsserver.ini 파일의 언어 변경 화면

  4. Using the following command, start the MCCS service for the both nodes.

    Start MCCS Service
    service mccs_agent start
  5.  After accessing the MCCS web console, check the changes made.

  • No labels