| | | | | |
|---|
1 | err | Failed to send reply genl due to error sending genl reply
| 오류로 인해 응답 genl 전송을 실패했습니다. cli 명령 결과를 수신하지 못합니다. | | bsr/bsr_nl.c:169
|
2 | err | Failed to finish bsradm due to cmd(%u) error: %s
| 오류로 인해 cli 명령 결과를 수신하지 못했습니다. | 로그에 출력 된 cmd, error 확인이 필요합니다. | bsr/bsr_nl.c:539
|
3 | err | Could not call %s user-space helper: error %dout of memory
| 메모리 오류로 사용자가 등록한 helper 호출을 실패했습니다. 등록한 helper가 실행되지 않습니다. | 로그에 출력 된 error 확인이 필요합니다. | bsr/bsr_nl.c:920
|
4 | err | Failed to set outdate peer due to not connected. cstate(%s)
| 피어 노드와 연결되어있지 않아 피어 노드 디스크 outdate 설정을 실패했습니다. | | bsr/bsr_nl.c:976
|
5 | err | fence-peer() = 7 && fencing != Stonith !!!
| | | bsr/bsr_nl.c:1042
|
6 | err | fence-peer helper broken, returned %d
| 사용자가 등록한 fence-peer helper가 잘못되었습니다. 등록한 helper가 실행되지 않습니다. | | bsr/bsr_nl.c:1048
|
7 | info | fence-peer helper returned %d (%s)
| 사용자가 등록한 fence-peer helper 실행 결과입니다. | | bsr/bsr_nl.c:1053
|
8 | info | Ignoring fence-peer exit code
| 사용자가 등록한 fence-peer helper 실행 결과를 적용하지 않습니다. | | bsr/bsr_nl.c:1064
|
10 | err | out of mem, failed to invoke fence-peer helper
| 메모리 부족으로 사용자가 등록한 fence-peer helper가 실패했습니다. 등록한 helper가 실행되지 않습니다. | | bsr/bsr_nl.c:1123
|
19 | err | Failed to get new device size due to all nodes diskless!
| 모든 노드가 diskless 상태이므로 디스크 사이즈를 얻는데 실패했습니다. 피어 노드와 연결이 종료됩니다. | | bsr/bsr_nl.c:2450
|
20 | err | Failed to get new device size due to requested disk size is too big (%llu > %llu)kiB
| 요청한 디스크 크기가 너무 커서 신규 디스크 사이즈를 얻는데 실패했습니다. 피어 노드와 연결이 종료됩니다. | | bsr/bsr_nl.c:2459
|
24 | info | discard zeroes data=0 and discard zeroes if aligned=no: disabling discards
| | | bsr/bsr_nl.c:2599
|
25 | info | peer BSR too old, does not support TRIM: disabling discards
| | | bsr/bsr_nl.c:2603
|
26 | info | WRITE_SAME disabled by config
| | | bsr/bsr_nl.c:2680
|
27 | info | peer does not support WRITE_SAME
| | | bsr/bsr_nl.c:2685
|
28 | info | Suspended AL updates
| activity log 사용을 중지했습니다. | | bsr/bsr_nl.c:2864
|
29 | info | Disable rs-discard-granularity feature in disk configuration
| rs-discard-granularity 옵션을 사용하지 않습니다. | resource 설정중 disk 섹션에서 rs-discard-granularity 으로 설정 할 수 있습니다. | bsr/bsr_nl.c:2928
|
30 | info | changed the rs-discard-granularity setting %u to %u
| rs-discard-granularity 옵션이 변경되었습니다. | resource 설정중 disk 섹션에서 rs-discard-granularity 으로 설정 할 수 있습니다. | bsr/bsr_nl.c:2946
|
34 | err | Failed to attach due to max capacity %llu smaller than disk size %llu
| 최대 디스크 사이즈가 설정 디스크 크기보다 작아 attach를 실패했습니다. | | bsr/bsr_nl.c:3681
|
35 | err | Failed to attach due to current (diskless) capacity %llu, cannot attach smaller (%llu) disk
| 디스크 사이즈가 작아서 attach를 실패했습니다. | 디스크가 용량이 충분한지 확인이 필요하며 로컬 디스크가 없는 primary 일 수 있습니다. | bsr/bsr_nl.c:3714
|
36 | info | The maximum number of bitmap peer devices is %u.
| 비트맵 최대 피어 수 입니다. | | bsr/bsr_nl.c:3812
|
37 | err | Failed to attach due to local node id %u differs from local node id %d on device
| 로컬 노드 ID와 device에 설정 된 노드 ID가 달라서 attach를 실패했습니다. | | bsr/bsr_nl.c:3819
|
38 | err | Failed to attach due to there is a bitmap for my own node id (%u)
| 노드ID로 소유한 비트맵이 있어 attach를 실패했습니다. | | bsr/bsr_nl.c:3829
|
39 | err | Failed to attach due to not enough free bitmap slots (available=%u, needed=%u)
| 사용 가능한 비트맵 슬롯이 부족하여 attach를 실패했습니다. | | bsr/bsr_nl.c:3850
|
40 | err | Failed to attach due to no latest data among peer devices with current UUID=%016llX
| 최신 데이터를 가진 peer_device 가 없으므로 attach를 실패했습니다. | exposed uuid가 설정되어있고peer_device 중 uptodate가 없을때 출력되는 로그입니다. | bsr/bsr_nl.c:3881
|
41 | info | Set all out of sync because of %s.
| attach 시 CRASHED_PRIMARY와 MDF_AL_DISABLED가 함께 설정되었거나, MDF_PEER_FULL_SYNC가 설정되었거나, Windows의 MDF_OS_SHUTDOWN_PENDING 종료 가드가 남아 있으면 해당 peer의 bitmap 전체를 OOS로 설정하기 직전에 출력합니다. Windows 종료 가드 복구는 bitmap 및 peer slot 검증 후 수행하며, 모든 대상 bitmap과 metadata 영속화가 성공해야 가드를 해제합니다. | 출력 사유는 crashed primary setting and activity log disable, peer full sync is set, OS shutdown did not complete 중 하나입니다. 이 로그만으로 bitmap 저장 또는 attach 성공이 보장되지는 않으므로 후속 오류와 상태 전이를 함께 확인합니다. | bsr/bsr_nl.c:4192
|
42 | info | Detach complete event wait timeout. time out(%ld) disk state(%s)
| detach 실행 대기시간을 초과했습니다. | | bsr/bsr_nl.c:4167
|
43 | err | Failed to attach due to failure to allocate %d size memory in kmalloc
| 동기화 시 사용하는 fifo 버퍼 할당 실패로 attach를 실패했습니다. | | bsr/bsr_nl.c:4590
|
44 | info | new peer device option. resync_rate : %uk, c_plan_ahead : %uk, c_delay_target : %uk, c_fill_target : %us, c_max_rate : %uk, c_min_rate : %uk, ov_req_num : %ub, ov_req_interval : %ums, repl_ratio : %u, resync_ratio : %u)
| 적용되는 peer device option 값 입니다. | resource 파일에서 설정 할 수 있습니다. | bsr/bsr_nl.c:4716
|
45 | info | default peer device option. resync_rate : %uk, c_plan_ahead : %uk, c_delay_target : %uk, c_fill_target : %us, c_max_rate : %uk, c_min_rate : %uk, ov_req_num : %ub, ov_req_interval : %ums
| 기본 peer device option 값 입니다. | resource 파일에서 설정 할 수 있습니다. | bsr/bsr_nl.c:4755
|
46 | err | Failed to new connection due to peer node id %u already exists
| 이미 피어 노드와 연결되어 있으므로 connection 생성을 실패했습니다. | | bsr/bsr_nl.c:4822
|
47 | err | Failed to add path due to failure to get an listener. err(%d)
| listener를 얻지못해 신규 path 추가를 실패했습니다. | 로그에 출력 된 err 확인이 필요합니다. | bsr/bsr_nl.c:5095
|
48 | err | Failed to delete path due to failure to put an listener. err(%d)
| listener을 찾지못해 path 제거를 실패했습니다. | 로그에 출력 된 err 확인이 필요합니다. | bsr/bsr_nl.c:5296
|
50 | info | Resync of new storage after online grow
| 새로운 공간의 동기화가 시작 됩니다. | | bsr/bsr_nl.c:5539
|
51 | err | Failed to resize due to requested %llu sectors, backend seems only able to support %llu
| 재설정 크기가 로컬 디스크 크기를 초과하여 디스크 크기 재설정을 실패했습니다. | | bsr/bsr_nl.c:5643
|
52 | err | Failed to I/O(%d) suspend due to not supported.
| I/O 일시 중단 기능을 지원하지 않습니다. | | bsr/bsr_nl.c:6279
|
53 | err | Failed to I/O(%d) resume due to not supported.
| I/O 재개 기능을 지원하지 않습니다. | | bsr/bsr_nl.c:6314
|
54 | info | Skip initial resync due to peer node disk state(%s).
| 신규 UUID 생성 시 초기 동기화를 하지않습니다. | | bsr/bsr_nl.c:7273
|
55 | err | Failed to create new uuid due to writing bitmap failed with err %d
| 비트맵 쓰기 오류로 새로운 UUID 생성을 실패했습니다. | 로그에 출력 된 err 확인이 필요합니다. | bsr/bsr_nl.c:7293
|
56 | err | Failed to create new resource due to invalid node id (%d)
| 설정 노드ID가 지원하는 최대 노드ID(32)를 초과하여 리소스 생성을 실패했습니다. | | bsr/bsr_nl.c:7404
|
57 | err | Failed to create new resource due to could not get a module reference
| 모듈을 참조 할 수 없어 리소스 생성을 실패했습니다. | | bsr/bsr_nl.c:7410
|
58 | info | Connection was not terminated during resource down. ret(%d)
| 연결 종료 실패로 down 명령을 실패했습니다. | | bsr/bsr_nl.c:7828
|
59 | err | Failed to notification resource state. error %d, event seq:%u
| 리소스 상태 이벤트 알림 전송을 실패했습니다. | 로그에 출력 된 error 확인이 필요합니다. | bsr/bsr_nl.c:7950
|
60 | err | Failed to notification device state. error %d, event seq:%u
| device 상태 이벤트 알림 전송을 실패했습니다. | 로그에 출력 된 error 확인이 필요합니다. | bsr/bsr_nl.c:8000
|
61 | err | Failed to notification connection state. error %d, event seq:%u
| 연결 상태 이벤트 알림 전송을 실패했습니다. | 로그에 출력 된 error 확인이 필요합니다. | bsr/bsr_nl.c:8052
|
62 | err | Failed to notification peer device state. error %d, event seq:%u
| peer_device 상태 이벤트 알림 전송을 실패했습니다. | 로그에 출력 된 error 확인이 필요합니다. | bsr/bsr_nl.c:8103
|
63 | err | Failed to notification path. error %d, event seq:%u
| path 상태 이벤트 알림 전송을 실패했습니다. | 로그에 출력 된 error 확인이 필요합니다. | bsr/bsr_nl.c:8406
|
64 | err | Failed to notification helper. error %d, event seq:%u
| helper 동작에 대한 이벤트 알림 전송을 실패했습니다. | 로그에 출력 된 error 확인이 필요합니다. | bsr/bsr_nl.c:8528
|
65 | err |