Connection information

At each node, you can check the access address/time and the user roles for the given ID.

[Figure] Conection Information

Feature settings

It is available to check features which are being used currently and to disable useless features.

If you disable, it is unable to use relevant resources, moreover, there may be features you cannot disable because the relevant resources have been registered already.

[Figure] Feature Settings

License settings

Can check the status of license for each node.

[Figure] License Settings

Log settings

Can adjust the color for each log message level and select the range of log information.

[Figure] Logging Setting

SNMP settings

The Simple Network Management Protocol(SNMP) is an internet-standard protocol that devices can share information about their current state using a message format.
SNMP provides a standardized framework and a common language used for the monitoring and management of devices in a network.
MCCS supports SNMP(Simple Network Management Protocal) trap and can send an event message to a device in a network. It supports SNMP version 1, version 2c and version 3. 

Configuring SNMP

You can add, edit, delete and view the SNMP configuration by select the node.

[Figure] Configuring SNMP

Adding SNMP

1) Select the 'Add' button in the bottom of the SNMP pane.

[Figure] Adding SNMP

2) Select the SNMP version and click the 'OK' button.

[Figure] Selecting SNMP version

3) Select the security level in case of version 3 and click the 'OK' button.

[Figure] Selecting security level

4) Enter the properties. If two or more values are entered, they will be separated by "," in destination IP. 

[Figure] Entering properties

    
[Figure] Entering properties of security level                                [Figure] Entering properties of security level                              [Figure] Entering properties of security level

Editing SNMP 

Select the 'Edit' button in the bottom of the SNMP pane.

[Figure] Editing SNMP   

Deleting SNMP

Select the 'Delete' button in the bottom of the SNMP pane.

[Figure] Deleting SNMP

[Figure] Warning message of deleting SNMP

Synchronizing the SNMP settings

When configuring of SNMP has complete, the properties are applied onto both nodes in the cluster. 
But this will be only applied on the node when the peer node is isolated in the cluster. In this case, this can be synchronized by clicking the 'Sync' button. 

[Figure] Synchronizing the SNMP settings.

[Figure] Warning message of synchronizing the SNMP

UI Config setting

It is available to check and modify information on the port to access to the UI.

And it also allows to check and modify how long a user had been being accessed that is shown as the session timeout item on the UI.

[Figure] The UI Config setting View

User settings

You can edit, add and delete an user account.

User account screen

You can check an account at each node.  

[Figure] User Account Setting 

Admin edit screen

You can change the password and language for admin ID.
You cannot change the user roles.

[Figure] User Account Setting 

[Figure] User Account editing 

Adding an account

1) Select the "Add user Account" in the bottom of the add "Account" screen.

  
[Figure] Adding Account in the User Account Setting

2) Enter the user ID, password, language, roles (Administrator/Monitor).

If you uncheck "Add User Accounts for Every Node", a new account will be set only for the current node in use.

[Figure] Adding an account

The following is the detail of user roles.

3) The screen is displayed after successfully adding it. You can see that an account is added to the Where User Account is Added node only.

[Figure] Finishing a Node Where User Account is Added

[Figure] Node Where User Account is Not Added

Modify the newly created account

You can modify the language and the user roles for this account.
You cannot change the user ID or password.

[Figure] Finishing a Node Where User Account is Added  

[Figure] User Account Modification

You can delete it from the both nodes or only from the current node.
But, you cannot delete the admin account.

[Figure] Newly Created Account Deletion  

 [Figure] Newly Created Account Deletion
   

You can refresh the screen to newly sort the user IDs at each node.

[Figure] Refreshing User Account

If different accounts are found at two nodes, you can unify them under the account on either node.
In addition, if the account file on one node is deleted, you can synchronize the account and retrieve it from the other node.

[Figure] User Account Synchronization