Configuration Type

FSR typically supports the following configuration types:

1:1

1:1 replication configuration for source and target nodes.

1:N

1: N replication configuration that simultaneously replicates one source node to multiple target nodes.

N:1

N:1 replication method with multiple nodes as source and one node as target.

Local Replication

This is a way to specify the source and target of replication to one node. It is used to do local backup or local migration without separate target node.

Shared Volume Replication

A configuration in which one source data is shared by two (active-standby) nodes and replicates this source data to a third target node. This approach is used when a shared volume is a SAN-like storage volume that is shared by two nodes simultaneously and replicated to DR in real time.

Periodic synchronization

This is the configuration method for volumes that will only perform periodic synchronization. They will not perform real-time replication. You can use this method to back up periodically, especially for volumes that cannot perform real-time replication, such as remote NFS shared volumes.

However, be sure to specify synchronization for NFS shared volumes as a source only, and not as a synchronization target. Because NFS shared volumes are written to by multiple clients, you cannot control the FSR engine as a single synchronization target. For more information on this, see Periodic synchronization in the appendix.

Configuration File

The configuration file is a json format text file that describes the configuration type and attributes of the replication. It is described as a system configuration file and a resource configuration file. The system configuration file specifies node global paths necessary for FSR operation, and the resource configuration file describes the specifics of replication such as ip address, replication target, and handler. Basically, the configuration file should be created by hand. If you want to change the properties of a running resource, modify the configuration file and apply it by executing adjust command using CLI or REST-API.

The FSR engine prepares replication services by interpreting configuration files at resource startup and initializing node-to-node connections and replication target paths according to the configuration.

For details on the configuration file format, refer to Attributes.

System Config.

The system configuration file is a config.json file. If you do not specify a separate path, it is located in the path in %FSR_HOME%/conf/config.json.

After modifying the configuration file, run the program again or run the following update command.

fsradm config adjust

Resource Config.

The file format of the resource file is '*.res' and the path is specified in the 'options/resource_path' entry in the system configuration file.
The default value of resource_path is the current location ('.') and based on the location of the system configuration file, the default location is the same as the location of the config.json file.

The following is an example of a resource configuration file.

{
  "id": "r0",
  "description": "test resource",
  "auto_start": true,
  "nodes": [
    {
      "name": "node1-hostname",
      "urls": {
        "repl": "10.20.200.75:9810",
        "sync": "10.20.200.75:9811"
      },
      "directories": [
        {
          "path": "G:/test/r0",
          "exclude_patterns": [
          ]
        }
      ]
    },
    {
      "name": "node2-hostname",
      "urls": {
        "repl": "10.20.200.76:9810",
        "sync": "10.20.200.76:9811"
      },
      "directories": [
        {
          "path": "G:/test/r0",
          "exclude_patterns": [
          ]
        }
      ]
    }
  ],
  "connections": [
    {
      "node1": {
        "name": "node1-hostname"
      },
      "node2": {
        "name": "node2-hostname"
      },
      "buffer": {
        "size": 1024
      },
      "network": {
        "ping_interval": 10,
        "compress": false,
        "tls": false,
        "limit": 0
      }
    }
  ],
  "options": {
    "exclude_patterns": [
    ]
  }
}

Basic Config.

• Describes an ID to identify a resource.
• The replication target nodes are described in an array format in the nodes item. Describe the hostname, ip address: port in the node entry. You can also describe the name entry by IP address without describing hostname.
• The replication target is described as directories and files in the directories item. If necessary, provide additional exclusion patterns.

Connection Config.

Unless otherwise noted in the connections entry, all replicated nodes individually establish TCP connections. This is called a mesh network. In a mesh network, duplicate connections for n nodes are created by n * (n-1) / 2.

If you need to limit the replication connection or describe the connection information according to the operating situation, additionally describe the “connections” item. connections describes an individual connection as an array.

Each connection is a connection to two nodes and is described in the fixed items of node1 and node2. The node1.name and node2.name entries describe the same name as described in the node entry above so that the node entries match the connections.node1 and connections.node2 entries.

In the normal case, the network is replicated by configuring a mesh network instead of configuring individual connections.

Exclusion Pattern

Files that need to be excluded from the replication target can be excluded from the replication target through the exclusion pattern. Exclusion patterns can easily be described using wildcard (*,!) Symbols.

Buffer Config.

In asynchronous replication, real-time I/O changes are accumulated in the buffer and reflected in the target sequentially so that the target data can be kept up to date as long as buffering continues. Therefore, configuring a buffer is the most important aspect of FSR configuration. Before starting resources, the buffer capacity must be configured according to the operating environment.

The buffers are provided as kernel memory buffers that are fixedly allocated to the kernel (nonpaged pool) and file buffers that are allocated as files. Since the available kernel memory of the system is limited, it is necessary to estimate the memory buffer according to the memory situation of the system, and if the memory buffer space is insufficient, additional file buffers can be used. FSR takes priority of the memory buffer and switches to file buffering when the memory buffer is used up. If both buffers overflow, the buffering stops and the buffered data is discarded and moved to the resynchronization phase. Therefore, it is necessary to reserve as much buffering space as possible so that replication status remains.

In addition, these two types of buffers perform I/O to memory and files, so there is a fundamental difference in performance. In situations where the local system has a high I/O load, operating with more memory buffers is advantageous for performance.

Because buffers operate on a per-connection basis, for 1:N replication, you must separately specify as many as the number of connections.

Memory Buffer

Memory allocated by the kernel is limited in its available capacity. Allocating too much for the system's usable capacity can affect system performance and should be allocated at an appropriate level.

You can allocate up to several tens of gigabytes, and usually assign several gigabytes.

File Buffer

The file buffer can be allocated as much space as the space on the disk where the file buffer is located. Up to several tens of Tera Bytes can be allocated and can operate at large capacity, typically tens of gigabytes. If a file buffer is configured as a path of the system volume, it is recommended to operate as a separate disk path because file buffer read/write I/O can affect the overall system performance.

Configure DRX integration

To configure DRX integration for building a DR site, see Configuring file replication.